Product line 02
Pressure vessel and process equipment heads
Elliptical, torispherical, hemispherical, conical and flat heads for pressure vessels and process tanks — made to drawing, with the documentation a vessel fabricator has to hand to their own inspector.
Engineering line, engineering paperwork
A head is only as useful as the paper that travels with it. Every batch leaves with a dimensional report and a material certificate tied to the heat number, so your quality department can file it straight into the vessel's documentation pack.
Where a project needs more, we test in our own shop: radiographic, ultrasonic and magnetic particle inspection, with reports written to the acceptance criteria in your specification.
- Profiles: EHA 2:1 elliptical, THA torispherical, hemispherical, conical, flat, and non-standard profiled heads
- Sizes: equipment rated for Ø203 mm to Ø3000 mm outside diameter; production to date sits in the smaller sizes, and any diameter we have not run before starts with a dimensioned first article
- Thickness: 0.6 mm to 20 mm
- Materials: 304/2B, 304/BA, 30408, 201, Q235B, Q345B, SA-36, SA-414G and 5083-O aluminium — 316L / 304L, Q345R and other grades on request
- Documentation: dimension report, material certificate, NDT report, and third-party inspection welcomed — your own inspector or SGS / BV / TÜV can attend the plant and witness the NDT
Cross-sections we quote most often: 2:1 elliptical, torispherical, hemispherical, conical and flat.
Applications
Pressure vessels
Air receivers, separators, accumulators and general pressure equipment.
Gas and cryogenic
LNG vehicle cylinders, Dewar flasks, stainless beverage kegs and coolers, and cryogenic service where aluminium and stainless are used.
Process industry
Reactors, fermentation tanks, mixing vessels, distillation and chemical equipment — and boilers, which are one of the longest-running uses of EHA and THA heads.
Food, pharma and water
Sanitary tanks and vessels where surface finish and cleanability matter.
Heads off the press
Finished parts photographed at the plant — elliptical and dished profiles with pressed openings, plain heads, and a mirror-polished head for a sanitary application.
Finished heads, photographed at the plant: elliptical and dished profiles with pressed openings, plain heads, and a mirror-polished head for a sanitary application.
Head types, sizes and tolerances
| Code | Head profile | Reference standard (form) | Outside diameter | Wall thickness | Typical use |
|---|---|---|---|---|---|
| EHA | Elliptical head, 2:1 (D/2h = 2) | GB/T 25198 · ASME VIII Div.1 UG-32(d) form | Ø203–3000 mm | 1.5–20 mm | Storage and pressure vessels, air receivers, jacket vessels |
| THA | Torispherical (dished) head | GB/T 25198 · DIN 28011 form | Ø203–1500 mm | 0.6–12 mm | Solar water heaters, heat-pump cylinders, low-pressure tanks |
| HHA | Hemispherical head | GB/T 25198 · ASME VIII Div.1 UG-32(e) form | Ø300–3000 mm | 2–16 mm | High-pressure vessels, LNG service, cryogenic Dewar flasks |
| CHA | Conical head | GB/T 25198 · customer drawing | Ø300–1500 mm | 2–16 mm | Hoppers, conical bottoms, separators, silos |
| FHA | Flat head / flat bottom | GB/T 25198 · customer drawing | Ø200–3000 mm | 2–20 mm | Tank bottoms, covers, low-pressure closures |
| Custom | Non-standard and profiled heads | To drawing | Up to Ø3000 mm | 0.6–20 mm | Necked openings, lift pads, manways, stepped and dished profiles |
Dimensional tolerances are held to GB/T 25198 for the head forms above. When your specification calls for a different acceptance basis — a dimensional table on your drawing, an ASME or EN-based form, a tighter roundness or a minimum-thickness rule — tell us at enquiry stage and we will confirm what we can hold before quoting.
One thing we would rather you hear from us than find out later: EHA and THA pressure vessel heads are the newest part of this plant's work, starting in 2019. The forming experience behind them goes back to 2001 in solar tank heads, and the presses, tooling and inspection equipment are the same. If your tender asks for decades of vessel-head references, that is a fair question — ask it at enquiry stage and we will answer it straight.
Request a quote
Send a drawing or a size list and we will quote head by head.
Open the RFQ form[email protected]
Quotes usually go out within one working day. Drawings stay confidential.